Spool Control Configuration
Spool Control Configuration Published: February 15, 2018 Spool Control Configuration allows default parameters to be configured in regards to FLEX report processing. Spool Control Configuration is found under System Administration in the FLEX Main Menu.
Days to Retain Reports in Output Queue
DLY – Any report generated on a daily basis, such as ACH Processing, Automatic Transfer Posting, etc. Recommended setting is 60 days to remain on server.
EOD – Any report generated when End of Day processes, such as teller balancing reports and GL Trial Balance. Recommended setting is 90 days to remain on server.
EGL – Any report generated when the general ledger open period is closed, such as GL Trial Balance and YTD Analysis. Recommended setting is 185 days to remain on server.
FRM – Any report generated when a new loan is processed (special forms). Recommended setting is 4 days to remain on server.
HLD – Refers to reports generated by any process, but have been placed on hold within the printers out queue. Recommended setting is 18 days to remain on server.
Printing Defaults
Printing Defaults only apply to newly added reports. If the report(s) has never been generated before, the system will use these settings.
OutPut to Printer – Valid options are Yes, No or Hold. If Yes is entered, all newly added reports will default to print to the designated printer. If No is entered, all newly added reports will default to not print. If Hold is entered, all reports will remain on hold in the printers output queue and will not print until a user releases them to print.
Printer ID – Any new report will default to the printer ID entered here. This can be left blank which will direct the report to use the printer ID found in Workstation Configuration.
#Copies – Enter a default number of copies to print for new reports.
Duplex – Check box to allow new reports to default to two-sided printing. Duplex printing must be supported by the designated printer.
Purge Defaults
Purge Spool File – Indicates if document should be included to be purged at EOM for automatic purge.
Months Until Purge – If Purge Spool File is checked, indicate number of months to retain before a purge is entered for automatic purge at EOM.
Copy Spool Files to Document Microfiche Library?
This is not commonly used and is not recommended by FLEX. This method of backup takes up more space on the server and has been replaced with Document Manager. Check either Yes or No to default new reports in an output queue to create a copy in the microfiche library.
Form Control – Indicates printer control characters that replace the report files internal printer control characters. Valid options are:
- *NONE – No printer control characters are inserted into the report output file.
- *FCFC – Inserts the ANSI forms control characters. These control codes are understood by most microfiche processors. Optical Disk Catalog print and import routines also use *FCFC printer control characters.
- *PRTCTL – The PRTCTL keyword specifies the use of dynamic printer control. The data structure specified as the parameter data_struct refers to the forms control information and line count value.
- *S36FMT – Inserts the same printer control characters as the S/36 COPYPRT command (IBM).
Clear Library After Back-Up – If using microfiche, the library containing microfiche files can be backed-up. Once this back-up is complete, indicate whether that library should be cleared. If set to No, a manual deletion of reports may be necessary in or order to avoid duplicates.
Copy Spool Files to Document Management Systems?
Check either Yes or No to create a PDF copy of each output queue. FLEX recommended setting is Yes for all output queues. These settings only apply to newly added reports.
Copy Spool Files to I Drive?
Check either Yes or No to default new reports added to any of the designated output queues to copy to the i:drive. Typically, this is set to No for an entire group and maintained on the individual report level. This is most commonly used for reports such as the General Ledger Trial Balance report as a disaster recovery tool.
Form Control – Indicates the printer control characters that replace the report files internal printer control characters. Valid options are:
- *NONE – No printer control characters are inserted into the report output file.
- *FCFC – Inserts the ANSI forms control characters. These control codes are understood by most microfiche processors. Optical Disk Catalog print and import routines also use *FCFC printer control characters.
- *PRTCTL – The PRTCTL keyword specifies the use of dynamic printer control. The data structure specified as the parameter data_struct refers to the forms control information and line count value.
- *S36FMT – Inserts the same printer control characters as the S/36 COPYPRT command (IBM).
Code Page – Indicates how the form will be copied to the i:drive. Valid options are:
- *1252 – Copies form using the stream method.
- *437 – Copies form using the PCD method.
- *37 – Also copies form using the stream method, still uses ASCII format but in a different view.
Please refer to Document Manager Configuration in FLEX Academy for instructions on managing individual report settings.
Confidentiality Notice: This document is published by Computer Marketing Corporation/FLEX and is intended solely for its contracted clients. It may contain information that is privileged, confidential or otherwise protected from disclosure. Dissemination, distribution or copying of this document and any accompanying attached information by someone other than the intended recipient(s), or an employee or agent acting on behalf of the intended recipient, is strictly prohibited.